Afterburner KM RC Model • INSTALLATION in the Freewing Eurofighter Typhoon • (English/Français 4K)

Afterburner KM RC Model • INSTALLATION in the Freewing Eurofighter Typhoon • (English/Français 4K)

Beschreibung zum Video:
Thanks again KM RC Model !!!!!

Get yours at

? Buy your CNHL LiPo ➡️
? Buy your Universal Afterburner KM RC Model ➡️
❌ Buy your Planes Stands here ➡️

?? Hi folks ???

Thank you for watching this video and don’t forget to subscribe so you don’t miss anything (it’s free but it helps content creators a lot) ???

If you want to help me to expand my squadron ? or buy a specific plane to review, you can help me by making a small donation via my PayPal link

Thank you very much in advance my friends ???

?? Salut les copains ???

Merci d’avoir regardé cette vidéo et n’oubliez pas de vous abonner pour ne rien manquer (c’est gratuit et pourtant ça aide énormément les créateurs de contenus) ???

Si vous voulez m’aider à agrandir mon escadron ? ou que j’achète un avion en particulier, vous pouvez m’aider en faisant un petit don via mon lien PayPal

Merci beaucoup beaucoup d’avance les amis ???

? Follow me on Instagram :
⏰ TikTok :

You can buy my things here ⬇️
✈️ FMS planes & cars ➡️
? Jeti Rx and DS16 ➡️ @OpaleParamodels
?CNHL LiPo ➡️
✈️ Jets and more ➡️

???️ Freewing Eurofighter Typhoon 90mm EDF Jet PNP

1/11 scale
Wingspan : 1030mm (40.5in)
Length : 1450mm (57in)
Empty weight : 3124g
Weight of KM RC Model Afterburner : 22g
Weight of 2 tanks, 4 METEOR, 2 ASRAAM, 2 GBU : 177g
Flying weight : with full missiles, tanks + afterburner KM RC Model (22g) + CNHL 6S 4000mah 70C (691g) : 3876g
And 3699g without ordnance
Wingload : 125 g/dm2
Wing area : 31 dm2
Power : 3668-1960kv Brushless inrunner motor
ESC Hobbywing 120A with 8A BEC
12 blades EDF
9g hybrid digital servos x4
9g metal gear digital servos x2
17gr MG digital servos x3 (elevons and rudder)
LiPo 6S 5000-6000mAh (depends on their weight)
Rx 7 channels minimum (throttle, elevons x2, rudder (mix with nose steering wheel), gear, airbrake, reverse
Nylon hinges
EPO foam

❌ Book CG (gear up) : 215mm from wing root Leading edge but MAIDEN 235mm ! CNHL 6S 4000 70C (690g) all the way back and 20gr counterweight they give you in the rudder (hole where rudder servo comes from)

? My Triple Rates (low / mid / high) after 6th flight :
Wing Ailerons : 20mm/24mm/100%
Wing Elevator : 14mm/35mm/100%
Canard aileron (not scale…) : 13mm/15mm/100% measured leading edge
Canard elevator : 8mm/20mm/100% measured leading edge
Rudder : 20mm/27mm/100%

⏰ Flights with timers and voltage (checked few minutes after landing):
-1st filmed crosswind : CNHL 4000 70C CG235mm : 4m50 flight (4m18 motor) 3.74v
-2nd windy and fast : CNHL 4000 70C CG235mm : 3m14 flight (2m30 motor) 3.81v
-3rd filmed : CNHL 4000 70C CG235mm : 2m38 flight (2m13 motor) 3.83v
-4th WITHOUT ordnance (too nose heavy CG225mm) filmed : CNHL 4000 70C CG235mm : 3m38 flight (2m54motor) 3.77v
-5th with ordnance CG235mm, filmed : CNHL 4000 70C : 3m24 flight (2m54motor) 3.81v
-6th with ordnance CG235mm, hard aerobatics : CNHL 4000 70C : 3m45 flight (3m16motor) 3.74v

0:00 Présentation française
0:30 English presentation
1:37 Détails des futurs jets
2:03 Pour les Moteurs Outrunner
2:38 For outrunner motor
3:40 Curve your zip ties
4:19 V3 English instructions
5:05 Différentes Couleurs
5:33 Idol power on/off
6:10 Marche/arrêt LED au ralenti
6:50 Alarme voltage bas (3.5v)
7:52 Low voltage alarm (3.5v)
8:36 Installation on Freewing Typhoon 90mm
12:31 Feed wires to the front (⚠️Don’t do like I did and put the wires UNDER PLYWOOD ESC ⚠️)
14:04 Screw EDF
14:55 Y harness balance plug tip
15:52 Cable Y prise équilibrage
16:15 CAUTIONS ⚠️
16:40 Précautions ⚠️
17:08 Calibration !
17:28 Jeti (new AB function) wiring
18:38 Calibration
20:22 Change colors ?
22:22 Switch off idol LED
22:55 Testing
23:14 Check CG 235mm with this LED
24:02 In the dark…
24:43 www.kmrcmodel.com
25:05 Thanks ?? please SUBSCRIBE ?
25:38 Details photos (Afterburner, LiPo…)

#typhoon #afterburner #rcplane #eurofighter #eurofightertyphoon #jeti #opale #radiocontrol #spanish #modellbau #new #foam #rc #aviation #release #unboxing #kmrcmodel
Subscribe on Youtube: Arthur RC, click here
Freitag – Newsletter zu allen aktuellen Videos der Woche aus 17 Channels, jetzt anmelden!

Vollständiger Text aus dem Video: Afterburner KM RC Model • INSTALLATION in the Freewing Eurofighter Typhoon • (English/Français 4K)
Hinweis: Text aus der automatischen Spracherkennung aus dem Video ist allgemein bekannt ungenau!

foreign [Music] ER was a so guys today we will unbox and install the kmrc model Universal afterburner a big thanks to a 2km RC model so a big big thank you a big thanks for uh for all these after burners so I’ve got uh two uh two Jewel After Burner there is one for the x-fly B1 7 millimeters DF which will uh should be should be there this summer we will see and there is also another one there is another another double a dual afterburner and this one will be for the FMS suhoi 27. this is a twin 70 millimeters also which will be there the the suhay should be there in uh in two months foreign [Music] foreign ER foreign metal strings that you you could uh you could use to um to fix your After Burner on a OutRunner motor you just have to uh to do it like that a new and you put it around the EDF a new tape and you tape that around your EDF with some uh some zip tie to secure it so yeah you can see that in this one you’ve got some zip ties to uh to fix the After Burner on your in-runner motor but I don’t have any on this one because it it was a it was for an out an OutRunner but it will be okay I have some so no big deal for that so now I’ve got some zip ties you have to curve it you see you have to curve that you will understand why after um foreign I see a donated [Music] you can find the instruction sheet on the on their website on the Kiama RC model there are many different colors as you can see here the first one this is default mode this is a brand new version the V3 with some yellow to blue and then blue with yellow and in the center that’s very very scale very beautiful the first mode is very nice the second one is yellow and blue and purple at Full Throttle the third one is only blue and the four is only yellow is [Music] um blue element the idle power because the default is a idle power on so it means that the the lead is a the light is on even when you are on idle throttle so um that’s not scale at all so I will uh I will switch off that idle power and so pressing the button for three seconds and the red light flash once on the afterburn alarm glows when throttle at zero and off the afterburner lamp is off TV um foreign foreign [Music] important [Music] portions questions reset so you have seen guys how to do you just have to short press the button once to change the voltage and then you you just have to read the the red the red LED which is right there you can see right here there is a small LED on the control board and so if it flash once this is a low voltage low voltage alarm on a 3.4 if it’s flashed twice 3.5 three times three six and four times three seven and be careful when you do that short press the throttle should be over five percent so that’s for the instruction the global instructions now we will install that on my firming eurofighter 90 millimeters feed zip tie through venting holes bend the zip tie first be careful not to damage motor wires so so so flexor yeah come over this way guys you see like that with the wire from the afterburner just on the same side as the mature here you go that’s good and one same for the other one yeah easy all right hang on you could add a bit a small amount of glue if you want but I won’t apologize foreign make sure the power wire um tutorial no one comes to see you all right nice very nice perfect that’s ready uh I’m really really tough It’s a really tight up and so then you can cut the excess mounting bars and zip tie make sure the LED lamp is secure nice and firm so now no no [Music] and we are good to go now we’ll have to feed The Wire foreign let’s see [Music] foreign good very easy it’s here it’s already there to do that okay so that’s good I will now I hope it will fit with the before created uh yes that’s perfect I don’t know if you can see but right here at the the back there is nothing against the there is nothing against the afterburner so now we will screw back the idiot foreign [Music] never over tight this Cruise because it’s plastic it’s like that all right I’ve got my voltage sensor if you are like me and you use your balance plug for another Telemetry things so like me with this voltage sensor you will uh you could build a y balance you see why by balance wire like that you can plug your sensor and then on the other side you plug the you plug the the After Burner and like that you can have the Telemetry and the light the afterburner um limitations so caution do not keep do not keep the unit at maximum brightness when there is no one thing yeah when it’s not flying of course it will overheat this is for 6s battery with a balance lead do not modify the control board wire LED do not remove the clear heat shrink wrapping around the land the the LED lamp before maximal control but I don’t care because I put I will put the the LED on a free Channel on my uh on my JT uh receiver 10 channels so I will put that in there in the 10 uh tick tick tick so I’ve created a function after a burner and with the the throttle stick you see so this is the same command as the throttle burner combustion is so connect the signal cable to throttle Channel with a Y wire it’s not included or on a spare Channel as I have just done no over connected comes apply power to the receiver apply through throttle cushion if did not disconnect the motor if we met plan yet connect the balance lead connect the balance lead to now the controller will start blinking slowly rapidly bling rapid blinking indicates a signal from okay so it should blink slowly apply power to the receiver apply Full Throttle apply Full Throttle and connect the balance lead after the controller blinks slowly for three four times lower the throttle to the desire position ah it works too foreign make sure fatal is set at zero short press the button to change the color red lead flash once and this is blue only blue so that’s the mud three all right I push one again and it should be only yellow yeah that’s only yellow and if I push once again it will be mod 1. foreign [Music] yes blue with yellow Center yes that’s it with yellow well check I will push once again to see what do we have now I am a synonym classical [Music] so this is up foreign all right cool now I will uh switch off the idle power so pressing the button for three seconds red flash flash once great it works and now when I apply my throttle it will start blinking at throttle yes that’s it after at all it starts to oh foreign no nothing has changed let’s see in there in the dark awesome Osama Sam This Is the End so uh don’t hesitate and go check their website on a km model that’s a very very easy to set up as you have as you have seen that’s very very cool this is a universal After Burner from a km RC model very nice thank you so much guys thank you so much for watching a big thanks to uh to kmrc and uh see you very soon for a flight video I hope this is bye foreign [Music] [Music] foreign [Music]
Für den Inhalt des Videos ist der VideoCreator: Arthur RC verantwortlich.
#Afterburner #Model #INSTALLATION #Freewing #Eurofighter #Typhoon #EnglishFrançais
arthur rc, source